/*-----------------------------------------------------------. / Black Mesa Source preset / '-----------------------------------------------------------'/ These are the settings I'm currently using for Black Mesa. I've lowered the SMAA_THRESHOLD to 0.08 to catch some edges that went undetected and I'm using very conservative sharpening, vibrance and vignette. - CeeJay.dk /*-----------------------------------------------------------. / Choose effects / '-----------------------------------------------------------*/ // Set to 1 for ON or 0 for OFF #define USE_SMAA_ANTIALIASING 1 #define USE_LUMASHARPEN 1 // Also sharpens the antialiased edges which makes them less smooth - I'm working on fixing that. #define USE_BLOOM 0 // Bloom makes bright lights bleed their light into their surroundings (relatively high performance cost) #define USE_HDR 0 // Not actual HDR - It just tries to mimic an HDR look (relatively high performance cost) #define USE_TECHNICOLOR 0 #define USE_TONEMAP 0 #define USE_VIBRANCE 1 // Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation. #define USE_SEPIA 0 #define USE_VIGNETTE 1 // Darkens the edges of the image to make it more look like it was shot with a camera lens. May cause banding artifacts. #define USE_DITHER 0 // Applies dithering to simulate more colors than your monitor can display. This lessens banding artifacts. /*-----------------------------------------------------------. / SMAA Anti-aliasing settings / '-----------------------------------------------------------*/ #define SMAA_THRESHOLD 0.08 // (0.08-0.20) Edge detection threshold #define SMAA_MAX_SEARCH_STEPS 16 // [0-98] Determines the radius SMAA will search for aliased edges #define SMAA_MAX_SEARCH_STEPS_DIAG 6 // [0-16] Determines the radius SMAA will search for diagonal aliased edges #define SMAA_CORNER_ROUNDING 20 // [0-100] Determines the percent of antialiasing to apply to corners. // -- Advanced SMAA settings -- #define COLOR_EDGE_DETECTION 1 // 1 Enables color edge detection (slower but more acurate) - 0 uses luma edge detection (faster) #define SMAA_DIRECTX9_LINEAR_BLEND 0 // Using DX9 HARDWARE? (software version doesn't matter) if so this needs to be 1 - If not, leave it at 0. /*-----------------------------------------------------------. / LumaSharpen settings / '-----------------------------------------------------------*/ // -- Sharpening -- #define sharp_strength 0.6 // (0.2-2.0)Strength of the sharpening #define sharp_clamp 0.035 // [0.0-1.0]Limits maximum amount of sharpening a pixel recieves - Default is 0.050 // -- Advanced sharpening settings -- #define pattern 2 // Choose a sample pattern [ 1, 2, 3 or 4 ] - I suggest 2 #define offset_bias 1.0 // [0.0-6.0](1.0) Offset bias adjusts the radius of the sampling pattern. // I designed the pattern for offset_bias 1.0, but feel free to experiment. // -- Debug settings -- #define splitscreen 0 // Enables the before-and-after splitscreen comparison mode. Left side is before. #define show_sharpen 0 // Visualize the strength of the sharpen (multiplied by 4 to see it better) /*-----------------------------------------------------------. / Bloom settings / '-----------------------------------------------------------*/ #define BloomThreshold 20.25 #define BloomPower 1.446 #define BloomWidth 0.0142 /*-----------------------------------------------------------. / HDR settings / '-----------------------------------------------------------*/ #define HDRPower 1.40 // Strangely lowering this makes the image brighter #define radius2 0.95 // Raising this seems to make the effect stronger and also brighter /*-----------------------------------------------------------. / TECHNICOLOR settings / '-----------------------------------------------------------*/ #define TechniAmount 0.11 #define TechniPower 2.8 #define redNegativeAmount 0.88 #define greenNegativeAmount 0.88 #define blueNegativeAmount 0.88 /*-----------------------------------------------------------. / Tonemap settings / '-----------------------------------------------------------*/ #define Gamma 1.0 #define Exposure -0.1 #define Saturation 0 #define Bleach 0 #define Defog 0.01 #define FogColor float4(2.55, 2.55, 0, 0) /*-----------------------------------------------------------. / Vibrance settings / '-----------------------------------------------------------*/ #define Vibrance 0.1 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation. /*-----------------------------------------------------------. / Sepia settings / '-----------------------------------------------------------*/ #define ColorTone float3(1.12, 0.66, 0.20) #define SepiaPower 0.11 #define GreyPower 0.88 /*-----------------------------------------------------------. / Vignette settings / '-----------------------------------------------------------*/ #define VignetteRadius 1.40 // lower values = stronger radial effect from center #define VignetteAmount -0.8 // Strength of black. -2.00 = Max Black, 1.00 = Max White. #define VignetteSlope 8 // How far away from the center the change should start to really grow strong (odd numbers cause a larger fps drop than even numbers) #define VignetteCenter float2(0.500, 0.500) // Center of screen for effect. /*-----------------------------------------------------------. / Dither settings / '-----------------------------------------------------------*/ //No settings yet, beyond switching it on or off in the top section.