19 minutes ago
MyRebornFXSNO.ver
/*-----------------------------------------------------------.
/ Choose effects /
'-----------------------------------------------------------*/
// Set to 1 for ON or 0 for OFF
#define USE_SMAA_ANTIALIASING 0
#define USE_LUMASHARPEN 1 //Also sharpens the antialiased edges which makes them less smooth - I'm working on fixing that.
#define USE_BLOOM 1 // Bloom makes bright lights bleed their light into their surroundings (relatively high performance cost)
#define USE_HDR 1 // Not actual HDR - It just tries to mimic an HDR look (relatively high performance cost)
#define USE_TECHNICOLOR 1
#define USE_TONEMAP 1
#define USE_VIBRANCE 0 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation.
#define USE_SEPIA 0
#define USE_VIGNETTE 0 //Darkens the edges of the image to make it more look like it was shot with a camera lens. May cause banding artifacts.
#define USE_DITHER 0 //Applies dithering to simulate more colors than your monitor can display. This lessens banding artifacts.
/*-----------------------------------------------------------.
/ SMAA Anti-aliasing settings /
'-----------------------------------------------------------*/
#define SMAA_THRESHOLD 0.05 // (0.08-0.20) Edge detection threshold
#define SMAA_MAX_SEARCH_STEPS 32 // [0-98] Determines the radius SMAA will search for aliased edges
#define SMAA_MAX_SEARCH_STEPS_DIAG 16 // [0-16] Determines the radius SMAA will search for diagonal aliased edges
#define SMAA_CORNER_ROUNDING 25 // [0-100] Determines the percent of antialiasing to apply to corners.
// -- Advanced SMAA settings --
#define COLOR_EDGE_DETECTION 1 // 1 Enables color edge detection (slower but more acurate) - 0 uses luma edge detection (faster)
#define SMAA_DIRECTX9_LINEAR_BLEND 0 // Using DX9 HARDWARE? (software version doesn't matter) if so this needs to be 1 - If not, leave it at 0.
/*-----------------------------------------------------------.
/ LumaSharpen settings /
'-----------------------------------------------------------*/
// -- Sharpening --
#define sharp_strength 2.0 // (0.2-2.0)Strength of the sharpening
#define sharp_clamp 0.050 // [0.0-1.0]Limits maximum amount of sharpening a pixel recieves - Default is 0.050
// -- Advanced sharpening settings --
#define pattern 2 // Choose a sample pattern [ 1, 2, 3 or 4 ] - I suggest 2
#define offset_bias 1.0 // [0.0-6.0](1.0) Offset bias adjusts the radius of the sampling pattern.
// I designed the pattern for offset_bias 1.0, but feel free to experiment.
// -- Debug settings --
#define splitscreen 0 // Enables the before-and-after splitscreen comparison mode. Left side is before.
#define show_sharpen 0 // Visualize the strength of the sharpen (multiplied by 4 to see it better)
/*-----------------------------------------------------------.
/ Bloom settings /
'-----------------------------------------------------------*/
#define BloomThreshold 16.85
#define BloomPower 0.286
#define BloomWidth 0.282
/*-----------------------------------------------------------.
/ HDR settings /
'-----------------------------------------------------------*/
#define HDRPower 1.51 //Strangely lowering this makes the image brighter
#define radius2 1.04 //Raising this seems to make the effect stronger and also brighter
/*-----------------------------------------------------------.
/ TECHNICOLOR settings /
'-----------------------------------------------------------*/
#define TechniAmount 0.1
#define TechniPower 1.9
#define redNegativeAmount 1.24
#define greenNegativeAmount 1.31
#define blueNegativeAmount 1.31
/*-----------------------------------------------------------.
/ Tonemap settings /
'-----------------------------------------------------------*/
#define Gamma 0.91
#define Exposure -0.01
#define Saturation 0
#define Bleach -0.1
#define Defog 0.00
#define FogColor float4(4.25, 3.25, 3.0, 0)
/*-----------------------------------------------------------.
/ Vibrance settings /
'-----------------------------------------------------------*/
#define Vibrance 0.6 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation.
/*-----------------------------------------------------------.
/ Sepia settings /
'-----------------------------------------------------------*/
#define ColorTone float3(1.12, 0.66, 0.20)
#define SepiaPower 0.11
#define GreyPower 0.88
/*-----------------------------------------------------------.
/ Vignette settings /
'-----------------------------------------------------------*/
#define VignetteRadius 1.05 // lower values = stronger radial effect from center
#define VignetteAmount -1.0 // Strength of black. -2.00 = Max Black, 1.00 = Max White.
#define VignetteSlope 8 // How far away from the center the change should start to really grow strong (odd numbers cause a larger fps drop than even numbers)
#define VignetteCenter float2(0.500, 0.500) // Center of screen for effect.
/*-----------------------------------------------------------.
/ Dither settings /
'-----------------------------------------------------------*/
//No settings yet, beyond switching it on or off in the top section.