Preset description:

/*-----------------------------------------------------------. / Choose effects / '-----------------------------------------------------------*/ // Set to 1 for ON or 0 for OFF #define USE_SMAA_ANTIALIASING 1 #define USE_LUMASHARPEN 1 //Also sharpens the antialiased edges which makes them less smooth - I'm working on fixing that. #define USE_BLOOM 1 // Bloom makes bright lights bleed their light into their surroundings (relatively high performance cost) #define USE_HDR 0 // Not actual HDR - It just tries to mimic an HDR look (relatively high performance cost) #define USE_TECHNICOLOR 0 // Attempts to mimic the look of an old movie using the Technicolor three-strip color process (Techicolor Process 4) #define USE_TONEMAP 1 #define USE_VIBRANCE 1 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation. #define USE_SEPIA 0 #define USE_VIGNETTE 0 //Darkens the edges of the image to make it more look like it was shot with a camera lens. May cause banding artifacts. #define USE_DITHER 1 //Applies dithering to simulate more colors than your monitor can display. This lessens banding artifacts (mostly caused by vignette) #define USE_DPX 0 //Unfinished - Should make the image look like it's been converted to DXP Cineon - basically it's another movie-like look similar to technicolor //I think the shader itself works, but the default settings need a lot of work. Maybe you can find some good settings? /*-----------------------------------------------------------. / SMAA Anti-aliasing settings / '-----------------------------------------------------------*/ #define SMAA_THRESHOLD 0.05 // [0.01 to 0.20] Edge detection threshold #define SMAA_MAX_SEARCH_STEPS 98 // [0 to 98] Determines the radius SMAA will search for aliased edges #define SMAA_MAX_SEARCH_STEPS_DIAG 16 // [0 to 20] Determines the radius SMAA will search for diagonal aliased edges #define SMAA_CORNER_ROUNDING 0 //25 // [0 to 100] Determines the percent of antialiasing to apply to corners // -- Advanced SMAA settings -- #define COLOR_EDGE_DETECTION 1 // 1 Enables color edge detection (slower but more acurate) - 0 uses luma edge detection (faster) #define SMAA_DIRECTX9_LINEAR_BLEND 0 // Using DX9 HARDWARE? (software version doesn't matter) if so this needs to be 1 - If not, leave it at 0. /*-----------------------------------------------------------. / LumaSharpen settings / '-----------------------------------------------------------*/ // -- Sharpening -- #define sharp_strength 1.5 // (0.2-2.0)Strength of the sharpening #define sharp_clamp 0.200 // [0.0-1.0]Limits maximum amount of sharpening a pixel recieves - Default is 0.035 // -- Advanced sharpening settings -- #define pattern 2 // Choose a sample pattern [ 1, 2, 3 or 4 ] - 1 = Fast, 2 = Normal, 3 = Wider, 4 = Pyramid shaped. #define offset_bias 0.9 // [0.0-6.0](1.0) Offset bias adjusts the radius of the sampling pattern. // I designed the pattern for offset_bias 1.0, but feel free to experiment. // -- Debug settings -- #define splitscreen 0 // Enables the before-and-after splitscreen comparison mode. Left side is before. #define show_sharpen 0 // Visualize the strength of the sharpen (multiplied by 4 to see it better) /*-----------------------------------------------------------. / Bloom settings / '-----------------------------------------------------------*/ #define BloomThreshold 20.25 #define BloomPower 1.446 #define BloomWidth 0.0142 /*-----------------------------------------------------------. / HDR settings / '-----------------------------------------------------------*/ #define HDRPower 1.20 //Strangely lowering this makes the image brighter #define radius2 0.85 //Raising this seems to make the effect stronger and also brighter /*-----------------------------------------------------------. / TECHNICOLOR settings / '-----------------------------------------------------------*/ #define TechniAmount 0.11 #define TechniPower 2.8 #define redNegativeAmount 0.88 #define greenNegativeAmount 0.88 #define blueNegativeAmount 0.88 /*-----------------------------------------------------------. / Tonemap settings / '-----------------------------------------------------------*/ #define Gamma 1.1 #define Exposure 0.0 #define Saturation 0.0 #define Bleach 0.0 #define Defog 0.010 //How much of the color tint to remove #define FogColor float3(0.00, 0.00, 2.55) //what color to remove - default is blue /*-----------------------------------------------------------. / Vibrance settings / '-----------------------------------------------------------*/ #define Vibrance 0.50 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation. /*-----------------------------------------------------------. / Sepia settings / '-----------------------------------------------------------*/ #define ColorTone float3(1.40, 1.10, 0.90) #define SepiaPower 0.58 #define GreyPower 0.11 /*-----------------------------------------------------------. / Vignette settings / '-----------------------------------------------------------*/ #define VignetteRadius 1.00 // lower values = stronger radial effect from center #define VignetteAmount -1.00 // Strength of black. -2.00 = Max Black, 1.00 = Max White. #define VignetteSlope 8 // How far away from the center the change should start to really grow strong (odd numbers cause a larger fps drop than even numbers) #define VignetteCenter float2(0.500, 0.500) // Center of effect. /*-----------------------------------------------------------. / Dither settings / '-----------------------------------------------------------*/ //No settings yet, beyond switching it on or off in the top section. //Note that checkerboard pattern used by Dither, makes an image harder to compress. //This can make your screenshots and videos take up more space. ///////////////////////////////////////////////////////////////// ///////////////////////// Work in Progress ////////////////////// ///////////////////////////////////////////////////////////////// /*-----------------------------------------------------------. / Cineon DPX settings / '-----------------------------------------------------------*/ //I have yet to find good default settings for this .. maybe you can? float Red = 8.0; //[1.0 - 15.0] float Green = 8.0; //[1.0 - 15.0] float Blue = 8.0; //[1.0 - 15.0] float ColorGamma = 2.5f; //[0.1 - 2.5] float DPXSaturation = 2.0f; //[0.0 - 8.0] float RedC = 0.4f; //[0.6 - 0.2] float GreenC = 0.36f; //[0.6 - 0.2] float BlueC = 0.35f; //[0.6 - 0.2] float Blend = 0.7f; //[1.0 - 0.0] How strong the effect should be

You need to be logged in to post a comment