3 minutes ago
Darker..Sharper..Reality
/*-----------------------------------------------------------.
/ Choose effects /
'-----------------------------------------------------------*/
// Set to 1 for ON or 0 for OFF
#define USE_SMAA_ANTIALIASING 1
#define USE_LUMASHARPEN 1 //Also sharpens the antialiased edges which makes them less smooth - I'm working on fixing that.
#define USE_BLOOM 0 // Bloom makes bright lights bleed their light into their surroundings (relatively high performance cost)
#define USE_HDR 1 // Not actual HDR - It just tries to mimic an HDR look (relatively high performance cost)
#define USE_TECHNICOLOR 0 // Attempts to mimic the look of an old movie using the Technicolor three-strip color process (Techicolor Process 4)
#define USE_TONEMAP 0
#define USE_VIBRANCE 1 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation.
#define USE_SEPIA 0
#define USE_VIGNETTE 0 //Darkens the edges of the image to make it more look like it was shot with a camera lens. May cause banding artifacts.
#define USE_DITHER 0 //Applies dithering to simulate more colors than your monitor can display. This lessens banding artifacts (mostly caused by vignette)
#define USE_DPX 0 //Unfinished - Should make the image look like it's been converted to DXP Cineon - basically it's another movie-like look similar to technicolor
//I think the shader itself works, but the default settings need a lot of work. Maybe you can find some good settings?
/*-----------------------------------------------------------.
/ SMAA Anti-aliasing settings /
'-----------------------------------------------------------*/
#define SMAA_THRESHOLD 0.12 // (0.08-0.20) Edge detection threshold
#define SMAA_MAX_SEARCH_STEPS 16 // [0-98] Determines the radius SMAA will search for aliased edges
#define SMAA_MAX_SEARCH_STEPS_DIAG 6 // [0-16] Determines the radius SMAA will search for diagonal aliased edges
#define SMAA_CORNER_ROUNDING 0 // [0-100] Determines the percent of antialiasing to apply to corners.
// -- Advanced SMAA settings --
#define COLOR_EDGE_DETECTION 1 // 1 Enables color edge detection (slower but more acurate) - 0 uses luma edge detection (faster)
#define SMAA_DIRECTX9_LINEAR_BLEND 0 // Using DX9 HARDWARE? (software version doesn't matter) if so this needs to be 1 - If not, leave it at 0.
/*-----------------------------------------------------------.
/ LumaSharpen settings /
'-----------------------------------------------------------*/
// -- Sharpening --
#define sharp_strength 1.25 // (0.2-2.0)Strength of the sharpening
#define sharp_clamp 0.05 // [0.0-1.0]Limits maximum amount of sharpening a pixel recieves - Default is 0.035
// -- Advanced sharpening settings --
#define pattern 3 // Choose a sample pattern [ 1, 2, 3 or 4 ] - 1 = Fast, 2 = Normal, 3 = Wider, 4 = Pyramid shaped.
#define offset_bias 1.0 // [0.0-6.0](1.0) Offset bias adjusts the radius of the sampling pattern.
// I designed the pattern for offset_bias 1.0, but feel free to experiment.
// -- Debug settings --
#define splitscreen 0 // Enables the before-and-after splitscreen comparison mode. Left side is before.
#define show_sharpen 0 // Visualize the strength of the sharpen (multiplied by 4 to see it better)
/*-----------------------------------------------------------.
/ Bloom settings /
'-----------------------------------------------------------*/
#define BloomThreshold 20.25
#define BloomPower 1.446
#define BloomWidth 0.0142
/*-----------------------------------------------------------.
/ HDR settings /
'-----------------------------------------------------------*/
#define HDRPower 1.37 //Strangely lowering this makes the image brighter
#define radius2 0.78 //Raising this seems to make the effect stronger and also brighter
/*-----------------------------------------------------------.
/ TECHNICOLOR settings /
'-----------------------------------------------------------*/
#define TechniAmount 0.11
#define TechniPower 2.8
#define redNegativeAmount 0.88
#define greenNegativeAmount 0.88
#define blueNegativeAmount 0.88
/*-----------------------------------------------------------.
/ Tonemap settings /
'-----------------------------------------------------------*/
#define Gamma 1.0
#define Exposure 0.0
#define Saturation 0.0
#define Bleach 0.0
#define Defog 0.010 //How much of the color tint to remove
#define FogColor float3(0.00, 0.00, 2.55) //what color to remove - default is blue
/*-----------------------------------------------------------.
/ Vibrance settings /
'-----------------------------------------------------------*/
#define Vibrance 0.16 //Intelligently saturates (or desaturates if you use negative values) the pixels depending on their original saturation.
/*-----------------------------------------------------------.
/ Sepia settings /
'-----------------------------------------------------------*/
#define ColorTone float3(1.20, 1.10, 0.90)
#define SepiaPower 0.6
#define GreyPower 0.15
/*-----------------------------------------------------------.
/ Vignette settings /
'-----------------------------------------------------------*/
#define VignetteRadius 1.00 // lower values = stronger radial effect from center
#define VignetteAmount -1.00 // Strength of black. -2.00 = Max Black, 1.00 = Max White.
#define VignetteSlope 8 // How far away from the center the change should start to really grow strong (odd numbers cause a larger fps drop than even numbers)
#define VignetteCenter float2(0.500, 0.500) // Center of effect.
/*-----------------------------------------------------------.
/ Dither settings /
'-----------------------------------------------------------*/
//No settings yet, beyond switching it on or off in the top section.
//Note that checkerboard pattern used by Dither, makes an image harder to compress.
//This can make your screenshots and videos take up more space.
/////////////////////////////////////////////////////////////////
///////////////////////// Work in Progress //////////////////////
/////////////////////////////////////////////////////////////////
/*-----------------------------------------------------------.
/ Cineon DPX settings /
'-----------------------------------------------------------*/
//I have yet to find good default settings for this .. maybe you can?
float Red = 8.0; //[1.0 - 15.0]
float Green = 8.0; //[1.0 - 15.0]
float Blue = 8.0; //[1.0 - 15.0]
float ColorGamma = 2.5f; //[0.1 - 2.5]
float DPXSaturation = 2.0f; //[0.0 - 8.0]
float RedC = 0.4f; //[0.6 - 0.2]
float GreenC = 0.36f; //[0.6 - 0.2]
float BlueC = 0.35f; //[0.6 - 0.2]
float Blend = 0.7f; //[1.0 - 0.0] How strong the effect should be